Learning to install a bathroom faucet is an easy project that will make a huge difference in your bathroom. Not only will it update the look of your vanity and sink but improvements like these increase the resale value of your home. This tutorial will teach you how to remove an old sink faucet and in install a new one. Replacing a faucet can be done in a few hours with simple tools.
I received a free faucet from Peerless in exchange for promotion on this blog. All opinions are mine alone.
How to Remove and Install a Bathroom Faucet
Hey Gnomies,
I’m getting close to finishing up my bathroom renovation. I’m pretty excited to be on the tail end of this project, It’s been taking up all of my (non-existent) free time for the past few months.
Trying to do home renovations when you have a four year old following you around all day can feel impossible at times but I promise you, it can be done, it might just take a little longer than you would like 😉
People often get intimidated by home improvement projects that are more “intermediate,” like plumbing jobs or tasks that involve power tools but I promise you, it’s really not that difficult. If you can operate a screwdriver, you can install a new faucet.
Check out the video for instructions on how to install a bathroom faucet and follow the instructions below.
Related: DIY Shiplap Accent Wall
Supplies used to remove and install a bathroom faucet
- Silicone sealant
- Wrench
- Screw driver
- Water supply hook ups
- Penetrating oil
- Safety goggles
Directions to Install a Bathroom Faucet
Step one: identify your current faucet
Before you buy a new faucet to replace the old one you need to make sure it will fit your sink. Your sink will have either one or three holes for the faucet. The holes will either be center set or widespread. The holes may be in the sink or in the countertop. Make sure you check and measure your sink before buying your new faucet.
In my case I have a three hole, widespread installation that will be going into the counter top.
Step two: Remove the Old Faucet
Before you can install the new faucet you need to take out the old one.
Make more room to work under the sink by clearing out all the soaps, shampoos and towels you store under the sink.
You may want to spray penetrating oil on the old tailpiece, mounting nuts, and supply tube coupling nuts. Wait 24 hours and so that the lube can do it’s magic and the whole de-installation will go a lot smoother.
First, you need to know where the water shut of valves are.
Start by shutting off the wall valves and turning on the faucet to drain out residual water in the pipes. You can also turn off the main water supply to the house if for some reason the valves won’t turn (but obviously none of the other water sources will work until you turn it back on)
Under the sink, there are typically nuts and washers securing the faucet. Remove any hardware in this area including the clamp bolt from the drain rod extension. Lift the faucet out from the top.
Use an adjustable wrench to loosen and remove the flexible extension from the faucet. Drain the remaining water into the bucket. Next, remove the flexible line from the shutoff valve.
Unscrew the mounting nut that is holding the flange and tailpiece onto the sink basin as far down as it will go.
Again, this may take an adjustable wrench
Disconnect the drain flange from the tailpiece.
Related: How to Remove a Bathroom Mirror
Step three: Clean up
If you are installing a new faucet into an existing sink that you’ve had for a while there may be some gunk and nasty stuff all up in there. Clean around the old drain and faucet holes. Mineral spirits can help remove old silicone sealant.
Now that we’ve got all of that business out of the way it’s time for the exciting part you’ve all been waiting for: Installing the new faucet
Step four: Install the new faucet
Depending on the type of faucet you purchased and whether it has three holes and the other factors we determined at the beginning the steps may vary slightly but in general installation is going to be the same.
Were are pretty much doing the de-installation, but in reverse.
Follow the manufacturer's directions for specific installation instructions.
Unscrew the nuts and washers off the bottom of the spout and hot and cold water handles. FYI, hot goes on the left and cold goes on the right.
Place the spout and handles through the mounting holes and secure from underneath with the washers and nuts.
Align the tabs and quick connects and snap them into place on the receiving tube.
Install the pop up assembly.
Apply just a little bit of silicone under the flange. Position the drain body on the bottom of the sink — making sure the pivot hole is facing the back — and screw the flange on from the top side.
Underneath, tighten the nut and gasket. On the top, use mineral spirits to clean up any excess silicone. Install the drain rod next. Unscrew the pivot nut on the drain body, insert the horizontal rod through the hole in the stopper, and replace the nut. Push the horizontal rod down and secure the lift rod to the strap with the screw. Test the lift rod.
Reconnect the supply lines to the faucet.
Related: OMG My husband painted the toilet gold!
Step five: Turn the water on
Turn the water valve back on and turn the water on. Test the faucet.
Check for leaks. If something is leaking you probably just need to tighten it up.
Check out the final bathroom reveal here and watch the video tour below:
Now you can enjoy your updated bathroom! Have you installed a faucet before? Let me know your best tips in the comments!
You may also like: Bathroom Makeover: Gross to Glam
Hi I’m Adrienne Carrie Hubbard. I believe a rich life comes not from the things you have, but the things you do; the experiences you create and the people you meet along the way. Thanks for hanging out!
SINCERELY COLLEEN says
Thanks for this! Such a simple tutorial. we have two bathrooms under renovation right now along with our kitchen. my husband knows how to install faucets, but i also love learning these things on my own! thanks for sharing!
xo, sincerely colleen